Search Results

This study has been conducted aiming at an experimental verification of the ring collapse phenomena that occurs in a taper faced second ring of a direct fuel injection type truck diesel engine. The oil film thickness of the second ring, the ring axial motion and the inter-ring pressure have been measured under various operating conditions of engine. As a result, it is verified that the back pressure of the second ring becomes lower than the second land pressure, and that the second ring oil film becomes extremely thick temporarily where the second ring contacts with the ring groove upper surface. It is also verified that blow-by passes through the second ring where the oil film of the second ring becomes thick. Hence it is highly probable that the collapse of the second ring has occurred at that time.

Fuel composition is investigated as a parameter influencing fuel/air mixing of direct injected fuel and the subsequent consequences for particulate emissions. Presumably, enhanced mixing prior to ignition results in a larger portion of fuel burning as a premixture and a smaller portion of diffusion burning around fuel-rich regions. This would potentially lower particulate emissions without overly compromising hydrocarbon emissions or high load operation. Using mixtures of n-paraffin fuels, particulate emissions were measured and the results were compared with in-cylinder visualization of the injection process and two-color method calculations of flame temperature. In general, lower boiling point fuels exhibited higher flame temperatures, less visible flame, and lower particulate emissions.

The effect of boiling point difference as well as the flash boiling of two-component normal paraffin fuels on combustion and exhaust emission has been examined under different test conditions. To obtain a wide variation in boiling point between components different high boiling point fuels (n-undecane, n-tridecane and n-hexadecane) were blended with a low boiling point fuel (n-pentane) and different low boiling point fuels (n-pentane, n-hexane, and n-heptane) were blended with a high boiling point fuel (n-hexadecane). In addition the volume fraction of n-pentane was varied to have the best mixture ratio with n-tridecane. These fuel combinations exhibit different potential for flash boiling based on a certain ambient condition. The results indicate that though the potential for flash boiling is the highest for a mixture of n-pentane and n-hexadecane it emits about 20% higher PM than a mixture of n-pentane and n-tridecane.

Although various factors affecting oil consumption of an internal combustion engine can be considered, a technique to predict the amount of oil consumed within a cylinder that passes across a running surface of a ring was developed in this study. In order to predict the effect of cylinder deformation on oil consumption, a simple and easy technique to calculate the oil film thickness in deformed cylinder was proposed. For this technique, the piston ring was assumed to be a straight beam, and the beam bends with ring tension, gas pressure, and oil film pressure. From the calculated oil film thickness, amount of oil passing across the running surface of the TOP ring and into the combustion chamber was calculated. The calculated results were then compared to the oil film thickness of the ring and oil consumption measured during engine operation, and their validity was confirmed.

A study was conducted to understand the effects the specifications of the crank-slider mechanism have on piston friction losses. The information obtained through the study is believed to be useful information for reducing the piston friction. A single-cylinder spark-ignited gasoline engine was designed and constructed to have not only a real-time piston friction measurement system using the floating liner method, but also provisions to facilitate changing the specifications of the crank-slider mechanism. This paper describes the study results obtained under various engine-operating conditions and reports the parametric test results of three crank ratios and five crankshaft-offset amounts tested.

A diesel fuel and air diffusion flame burner system has been designed for laboratory simulation of diesel exhaust gas. The system consists of mass flow controllers and a fuel pump, and employs several unique design and construction features. It produces particulate emissions with size, number distribution, and morphology similar to diesel exhaust. At the same time, it generates NOx emissions and HC similar to diesel. The system has been applied to test plasma discharges. Different design discharge devices have been tested, with results indicating the importance of testing devices with soot and moisture. Both packed bed reactor and flat plate dielectric barrier discharge systems remove some soot from the gas, but the designs tested are susceptible to soot fouling and related electrical failures. The burner is simple and stable, and is suitable for development and aging of plasma and catalysts systems in the laboratory environment.

As countermeasures against global warming caused by carbon dioxide, improvement of automotive fuel economy to lower CO2 emission becomes important. In order to promote less CO2 vehicles, appropriate methods to evaluate vehicle fuel economy performance are needed. However, the existing fuel economy test is limited to passenger cars and light duty trucks. The test is executed on a chassis dynamometer. However, if this test method is applied to heavy-duty vehicles (HDV), a large sized chassis dynamometer is needed. Furthermore, heavy duty vehicles have wide variations in a combination of an equipped engine, body shape, a transmission gear, a permissible limit of pay load, and so on. This leads to the increase in the number of chassis dynamometer tests. Therefore, it is difficult to use chassis dynamometer test to evaluate HDV fuel economy performance.

One of the phenomena accompanying the lightweight/compact/high power output feature of engines is the cylinder bore deformation, which may readily cause increased oil consumption, gas leakage, unusual wear, scuffing, etc.. The authors have had experiences that piston rings had generated contact failure during engine operation (1)*. Such deformation is generated as a combination of the static deformation due to head bolt tightening, crankshaft installation, etc., and the deformation by the operating factors; thermal load and combustion pressure. Countermeasure of design have been made for the former (2)*, and prediction of the deformation during actual operating have been tried using FEM analysis, etc. for the latter (3)*. Therefore, the accurate measurement result have been required strongly, for a long time. But it could not be realized in the past.

Degradation of the deNOx performance has been found in in-use heavy-duty vehicles with a urea-SCR system in Japan. The causes of the degradation were studied, and two major reasons are suggested here: HC poisoning and deactivation of pre-oxidation catalysts. Hydrocarbons that accumulated on the catalysts inhibited the catalysis. Although they were easily removed by a simple heat treatment, the treatment could only partially recover the original catalytic performance for the deNOx reaction. The unrecovered catalytic activity was found to result from the decrease in conversion of NO to NO2 on the pre-oxidation catalyst. The pre-oxidation catalyst was thus studied in detail by various techniques to reveal the causes of the degradation: Exhaust emission tests for in-use vehicles, effect of heat treatment on the urea-SCR systems, structural changes and chemical changes in active components during the deactivation were systematically investigated.

The use of biofuel is essential for the reduction of greenhouse gas emission. This paper highlights the use of biodiesel as a means of reducing greenhouse gas emission from the diesel engine of heavy-duty vehicles. Biodiesel is fatty acid methyl ester (FAME) obtained through ester exchange reaction by adding methanol to oil, such as rapeseed oil, soybean oil, palm oil, etc. The CO₂ emission from combustion of biodiesel is defined to be equivalent to the CO₂ volume absorbed by its raw materials or plants in their course of growth. On the other hand, however, biodiesel is known to increase the NOx emission when compared with operating with conventional diesel fuel, then suppressing this increase is regarded as a critical issue. This study is intended to identify the fuel properties of biodiesel free from increase in the NOx emission.

A new ignition-combustion concept named PCC (Plume Ignition Combustion Concept), which ignite rich mixture plume in the middle of injection period or right after injection of hydrogen is completed, is proposed by the authors in order to reduce NOx emissions in high engine load conditions with minimizing trade-offs on thermal efficiency. In this study fundamental requirements of hydrogen jet to optimize PCC are investigated by using single and multi-hole nozzle with a combination of high speed laser shadowgraphy to visualize propagating flame. As a result, it was infered that igniting the mixture plume in the middle of injection period with minimizing jet penetration to chamber wall is effective reducing NOx formation even further.

In recent years, start-stop systems have been implemented by many OEMs for improvement of fuel economy. When the engine stops, the occupant comfort typically deteriorates. Hence, the climate and fuel economy engineers are struggling to combine the passenger comfort and fuel economy. Especially in a vehicle cabin where the thermal environment becomes unsteady and highly non-uniform due to a start-stop. It is difficult to adapt any comfort evaluation index that have already been well established for a stationary/uniform space in building type environment in comparison to a vehicle cabin interior. The existing standard of ISO-14505-2 does not consider this for vehicle cabin interior condition. Hence, the authors have developed the occupant’s comfort prediction method under highly non-uniform condition and unsteady conditions and have established a new methodology [1].

As a result of WNTE regulations and the introduction of close-coupled aftertreatment systems, exhaust purification at high temperatures in commercial vehicles has become increasingly important in recent years. In this report, we improve the prediction accuracy for NOx conversion at high temperatures in the kinetic model of conventional Cu-selective catalytic reduction (Cu-SCR). Reaction rate analysis indicated that the rate of NH3 oxidation was extremely low compared to the rate of standard SCR. We found that NOx concentration-dependent NH3 oxidations (termed NOx-assisted NH3 oxidations) were key to the rate of NH3 oxidation. The output of the improved Cu-SCR kinetic model was in agreed with experimental results obtained from the synthetic gas bench and engine dynamometer bench. We analyzed the contribution of each reaction to NH3 consumption during Cu-SCR. Under NH3 + NO + O2, standard SCR was dominant at low temperature.

In recent years, attention has focused on smokeless, sulfur-free dimethyl ethyl (DME) as a clean fuel for heavy-duty diesel vehicles [1]. In this development, the DME engine applied for 20-ton GVW truck was developed under the auspices of the Ministry of Land, Infrastructure and Transport of Japan, the first known instance worldwide. With careful design of the fuel system considering DME's unique fuel characteristics and suitable combustion improvement, higher torque was obtained with DME, compared to diesel fueling. and also use of the proper EGR and catalyst, exhaust emissions levels were generally less than one-fourth of new long-term regulation value promulgated in 2005 Japan.

The 1997 Kyoto protocol came into effect in February, 2005 to reduce greenhouse gases within the period 2008-2012 by at least 5 % with respect to 1990 levels. Application of biodiesel fuel (BDF) to diesel engine is very effective to reduce CO2 emission, because BDF is carbon neutral in principle. The purpose of this project is to produce a light-duty biodiesel truck which can be suitable for emission regulation in next generation. The effect of BDF on the performance and emissions of modern diesel engine which was equipped with the aftertreatment for PM and NOx emissions was investigated without modifications of engine components and parameters, as a first step for research and development of biodiesel engine. Rapeseed oil methyl ester (RME) was selected in behalf of BDF, and combustion characteristics, engine performance and exhaust emissions were made a comparison between RME and petroleum diesel fuel by steady operation and Japan transient mode (JE05) tests.

Urea SCR (Selective Catalytic Reduction) system has high potential of reducing NOx. But such as system durability and safety under deteriorated catalysts conditions have not been well enough clarified because it is new technology for vehicles. In this paper, current NOx emission level of an engine equipped with urea SCR system is discussed and then exhaust emission characteristics were analyzed when the SCR catalyst and/or oxidation catalyst lose their functions. When both SCR and oxidation catalyst were de-activated, not only NOx but also PM increased remarkably, which were much more than the engine-out emissions. Oxidation catalyst downstream of SCR catalyst was effective to suppress such deteriorations.

Hydrogen is expected to be a clean and energy-efficient fuel for the next generation of power sources because it is CO2-free and has excellent combustion characteristics. In this study, an attempt was made to apply Homogeneous Charge Compression Ignition (HCCI) combustion to hydrogen with the aim of achieving low oxides of nitrogen (NOx) emissions and high fuel economy with the assistance of the di-methyl-ether (DME) fuel supplement. As a result, HCCI combustion of hydrogen mixed with 25 vol% DME achieved approximately a 30% improvement in fuel economy compared with HCCI of pure DME and spark-ignited lean-burn combustion of pure hydrogen under almost zero NOx emissions and low hydrocarbon (HC) emissions. This is attributed to control of the combustion process to attain the optimum onset of combustion and to a reduction of cooling losses.

According to authors' previous research, high pressure hydrogen engines with direct injection right before TDC and spark ignition obtain high performance and eliminate almost. abnormal combustion. This study has clarified the mooted points in the flame propagation to adjacent jets and the control of the optimum spark timing and large NOx emissions even in leaner than excess air ratio of λ=2. Nitric oxides (NOx) is the only the pollutant in the exhaust gases emitted by hydrogen engines. It has been found that the NOx formation largely depends on the mixture formation method. In order to operate the engine in a small amount of NOx, an experimental study was carried out to investigate the reduction of NOx and the output power by using dual mixture formation method, external mixture formation and direct injection.

An unique measurement method was developed for measurement of the piston outer surface during the engine operation. The method was realized by embedding a gap sensor into a cylinder bore and by rotating the cylinder in the circumferential direction. By means of this method, interesting data of skirt deformation of a gasoline engine caused by temperature, pressure and the slap force were obtained.

In order to establish hydrogen engines for practical use, it is important to overcome difficulties caused by unique characteristics of hydrogen fuel. A hydrogen engine with direct injection right before top dead center(TDC) and spark ignition has advantages such as prevention of abnormal combustion and realization of high power output near the stoichiometric air-fuel ratio, in comparison with an engine with external mixture. On the other hand, it has been pointed out that ignition and combustion for this type of hydrogen engines should be improved and that further studies on mixture formation of air and injected hydrogen are necessary for the improvement. For the direct injection hydrogen engine, mixture is formed both by air flow inside the combustion chamber and by injected hydrogen jet.